It has been a little while since the last update and a bit has been done.
I ended up booked to go to Subinats, and I wanted to have all the power before then. I booked in the dyno for the week before (start of October).
I knew there were a few bits I wanted to sort before the full power dyno run, so in September the car went back on the hoist.
The list of things I wanted to sort was as follows:
-add the varex muffler to allow the cutting of noise when doing highway driving
-refresh timing components (mainly fitting the RSD high RPM eccentric idlers)
-investigate the oil leak behind the timing cover
-add bracket to up-pipe to help support turbo
-add heat shielding to the exhaust
-add EGT sensors (or at least provisions for them) while the exhaust was off
-fix the catch can situation (the old one leaked and I didn't like the location)
-fix the slow leak from the gearbox seals
With the car on the hoist I pulled everything off, headers, up pipe, dump, timing parts.

With everything off I looked for the oil leak(s)...

And I couldn't find a single wet patch behind anything. Absolutely nothing.
I had thought my leak was probably from the reused seals in the AVCS sprockets, as when I had refreshed them last time, the seals weren't available separately. Company 23 now conveniently offers replacement seals separately to the assembly, so I had picked up a set in preparation. I was already in there, so I pulled them apart and put in the new seals.

The other reason I was in doing timing was to replace the secondhand IAG eccentric idler with a pair of 15,000RPM rated Rally Sport Design iders.

Again, it was a bit of a "while I'm in here" job, so I replaced the tensioner and the belt too.

Now, onto that leak that I was chasing... I posted to my insta story and a mate commented that he had the same symptoms when his power steering pump was leaking. After a bit more digging, lo and behold that was exactly the problem. It was leaking from basically everywhere. Subaru only sell the top o-ring separately, so I went digging for a seal kit for the whole pump.
I ended up going for this kit off ebay
"POWER STEERING PUMP SEAL KIT TO SUIT SUBARU LIBERTY TURBO 6/03 - 6/09 ( 8760)" (title in case the listing is removed, seller was Steering Rebuilds Australia P/L)
https://www.ebay.com.au/itm/172805696328It rocked up and seemed like it would do the job.
I pulled the whole pump and just dumped it in the ultrasonic because it was grot.

After a lot of scrubbing and cleaning it was ready to come apart. I used this video a fair bit for basic reference, but otherwise it really was a case of paying attention to how it came apart and putting it back together the same.
https://www.youtube.com/watch?v=oXjUaEGHAlUIt is worth mentioning this really was just a re-seal. My pump worked fine, it just leaked like a sieve, so if you have bigger problems, this probably isn't a solution. I also didn't do anything to the switch passthrough as mine wasn't leaking.

With it all back together though, it has worked perfectly ever since, no leaks, no problems.
Next up it was time to replace the gearbox seals (again). The Burson seals had never quite done the job, so with a set of Subaru replacements I set to work replacing them.
This went fine, right up until I split one of the outer sundial o-rings. Which in itself, wouldn't be a problem, but at this point I had a week before the dyno and needed the car back together.

Fortunately a few mates and a local bearing supplier were able to sort me out with replacements and the box went back together.
With the exhaust off a bracket was made to attach the up-pipe to the engine. Then holes were dilled for EGT bungs and I started to put heat shield on it.



Unfortunately after putting holes in the headers we discovered that there was a big crack in one of the primaries.

It could have been repaired, but given I wanted EGT bungs and heat shielding it just didn't seem worth putting all that effort into something that might just fail shortly anyway. It also probably could have been repaired before the dyno, but again, it is a lot of work for something that won't be sticking around. I bought a used set of headers and hoped they would arrive in time (this was maybe a week and a half before the dyno).
Fortunately they arrived two days before the dyno, so I was able to put them on the night before. They already had heat wrap, so because of time I left that on there, and I will cover them with the insulation and stainless sheet (as well as fitting EGT bungs) at a later date.

The rest of the exhaust was going to get a Varex muffler put in the centre to allow me to close the valve for quieter highway driving and cruising. Unfortunately the muffler was just too big to fit anywhere, so I jumped on marketplace and found a resonator to put in with the hope of achieving similar. I found a Dynomax muffler which seemed to fit the bill and it was only $100 on marketplace new in box. Honestly the workmanship on the Dynomax isn't amazing, and it is slightly low (speedbumps are slightly scrapy), but it went in and the car is a lot less droney on the highway.
The other thing I wanted to sort was the catch can. The original was poorly made, sat in a bad spot, and was just an eyesore (I made it).
I wanted something that was out of the way, had ports for both heads and the crank breather and also returned to the PCV and turbo inlet. I also wanted a cover to help isolate the intake from the bay.
I took a few basic scans with my phone (thank Kiri Engine) and imported them to fusion to see what room I had to play with.
I used a combination of CAD, cardboard, and aluminium to work out the exact spacing for everything.




I cut the cover from sheet with a grinder and got the catch can laser cut.
Once it arrived and I got it welded (by a mate), it went in

(just like the simulations)
The cover also got chopped (probably slightly too judiciously)

Everything was sort of half done the day before the dyno, I had been waiting for box seals, headers, and catch can to be welded. Somehow it all went together, with new catch can hoses going in, the exhaust bolting up. First fill with non-run in oil.

I drove it home (the exhaust wrap on the headers was very smokey). I finished the car at about 8:30pm, and I still had to get e85 for the dyno. I also needed some jerrys cans. Fortunately Bunnings is open until 9pm, so I hustled and made it in time to grab 3 jerrys. I then went to the closest united to fill them up... Of course, the after-hours machine was broken, so no e85 for me. The car also didn't want to boost properly, and sounded odd coming off boost (no choo choo, more a screech)
In the middle of the night I had the recollection that I didn't remember putting the throttle body clamp back on. I woke up early and went and checked, and I found the very obvious problem:
I also still needed e85, so I drove to the nearest servo to the dyno which has e85, and checked that the car made boost again while I was at it. Fortunately it was all good.
Then I headed for the dyno.

The car had some decent runs, but unfortunately there were a couple of issues that stopped us doing the full power tune, or e85 tuning.
The wideband sensor wasn't reading correctly, which is an instant no-go on the e85 tuning, but the AVCS wasn't behaving either, swinging wildly around the target. We weren't sure if the AVCS problem was mechanical or electrical, so given the wideband also needed replacing a decision was made to call it a day.
With that said, on 98 fuel and gate pressure (14psi) the car made 271kw.

A fair bit short of the goal, but nothing to be sniffed at. I could also now rev it to 8k, which is great even without a bucket of power.
So not the ideal outcome, but nothing went badly wrong and the car was at least good for the ~2500km trip to and from Sydney the next week.
The roadtrip went without a hitch, the exhaust was quieter, the car drove really nicely in every scenario that was thrown at it.
It made it to Subinats

I saw the sights

And then I drove it all the way back home.
It all went great...
Until I turned into my driveway. That's the exact moment the front driveshaft decided it didn't like being in the gearbox any more and dumped all the gearbox fluid on the ground.

I have since tried replacing the cir-clips


I have tried no circlips, different shafts, wailing on them with a hammer... And still nothing. The shafts seem to go all the way in, but there is no force retaining them, you can pull them back out by hand.
As it sits the car is on jack stands, as far as I can tell the shafts have never seated properly, I just got lucky right up until that moment. I have some stub shafts to try, but as it stands I don't trust the front diff install, so I will likely put the front end back together, put the car back on the hoist and drop the box and re-check the diff numbers.
Once that is sorted I still have to finish sorting the AVCS (a new wideband went in on the same afternoon as dyno day). The plan for that is to double check the banjos, and then look at the tune itself some more (I have checked the tune and got them closer, but it still doesn't seem as close as it should be).
Anyway, big update, thank for reading, hopefully the next one ends with the car back on all four wheels.