Member Profile - PUDZ RSC3.0RB

[PUDZ RSC3.0RB]

Great result grant

And that sounds unbelievable. No better subie sound than a supercharged h6 in my opinion

Mick

Thanx for ur comments and yeah I agree the sound is awesome and very unique, so happy with it. Yet so understated when cruising anywhere from 50 - 110kph.

[PUDZ RSC3.0RB]

Small upgrade completed recently, stock piece was shot. Went for the Torque Solution's variant.

100_1243.JPG (183.57 KiB) Viewed 4528 times

Photo0460.jpg (166.63 KiB) Viewed 4528 times

I can report no increase in NVH.

[PUDZ RSC3.0RB]

Have also installed the KAP Industries fire extinguisher bracket. Used 2 x 45mm long nylon spacers and longer bolts to give the bracket some clearance over my 3D mat.

Photo0458.jpg (182.04 KiB) Viewed 4525 times

Photo0459.jpg (176.07 KiB) Viewed 4525 times

Photo0465.jpg (168.76 KiB) Viewed 4525 times

Photo0467.jpg (176.41 KiB) Viewed 4525 times

[Tradewind]

You should have noted a power increase after the muff repair ........

[KiDo_Tuning]

Stop showing off with your PLX Devices install being neater than my 'everything shoved in a ripped plastic bag under the passenger seat' install

[bigBADbenny]

Awesome, where did you source the spacers and bolts?

[PUDZ RSC3.0RB]

You should have noted a power increase after the muff repair ........

Muffler still had fair flow, just very rattly and some gas leaks under.
More so improved low - mid torque a little as well as reducing hesitation in the same range, probably due to small leaks in bottom of muffler.

Intend to operate on replaced stock muffler, just to see if it can be fixed and/or improved.

[PUDZ RSC3.0RB]

Stop showing off with your PLX Devices install being neater than my 'everything shoved in a ripped plastic bag under the passenger seat' install

Ha Ha Matty, didn't even know the PLX was in the pics until I uploaded them . Mine too was a bit of a mess until it started pissin me off.

Howd ur Foz end up with the f....in hail?

Ill PM you soon about catching up next week sometime.

[PUDZ RSC3.0RB]

Awesome, where did you source the spacers and bolts?

Hey bBb

Spacers from local bearing services and bolts from local trade supplies. . I can have seat nearly fully forward and not see extinguisher from above as well
as clearing the 3D mat.

[KiDo_Tuning]

Stop showing off with your PLX Devices install being neater than my 'everything shoved in a ripped plastic bag under the passenger seat' install

Ha Ha Matty, didn't even know the PLX was in the pics until I uploaded them . Mine too was a bit of a mess until it started pissin me off.

Howd ur Foz end up with the f....in hail?

Ill PM you soon about catching up next week sometime.

Foz was at the Plaza. WRX, Lib and STi not so good Will show you when I get home, copped it worse than Kyles car!

[bigBADbenny]

Spacers from local bearing services and bolts from local trade supplies. . I can have seat nearly fully forward and not see extinguisher from above as well
as clearing the 3D mat.

Thanks for the info: I'll give it a try.

[zyweik]

Wonder what the legalities of said spacers would be? The nylon could crush in an accident and cause damage..maybe metal spacer would be the go?

[PUDZ RSC3.0RB]

Wonder what the legalities of said spacers would be? The nylon could crush in an accident and cause damage..maybe metal spacer would be the go?

The spacers ive used are actually engineered polymer bushes used in dynamic load-bearing applications, so I think they will be fine strength wise.

[PUDZ RSC3.0RB]

Stop showing off with your PLX Devices install being neater than my 'everything shoved in a ripped plastic bag under the passenger seat' install

Ha Ha Matty, didn't even know the PLX was in the pics until I uploaded them . Mine too was a bit of a mess until it started pissin me off.

Howd ur Foz end up with the f....in hail?

Ill PM you soon about catching up next week sometime.

Foz was at the Plaza. WRX, Lib and STi not so good Will show you when I get home, copped it worse than Kyles car!

PM sent mate. ^^^ Not looking forward to seeing the cars.

[PUDZ RSC3.0RB]

Thought id better document my latest couple of mods.

Photo0493.jpg (197.88 KiB) Viewed 4339 times

Photo0492.jpg (154.4 KiB) Viewed 4339 times

Courtesy of Avojdm and also a bit of engine bay bling with the sti strut brace - no pic of this as yet.

I must say along with a couple of new factory bushes the difference is night n day.

The shift now is awesome, no extra effort, very direct, nice n tight as we like , and about 30% less throw.