CRUISN's Gen2 JDM style surf wagon

by **[ITS-STI]** » Sun Mar 24, 2013 7:38 pm

Really? Dude, you are a magician! :meeting:

by **cruisn** » Sun Mar 24, 2013 10:11 pm

bigBADbenny wrote:I'd like to run the Nissans on the rear

Who's going to polish them for you? Certainly not me. :lol:

by **dazzz168** » Sun Mar 24, 2013 11:53 pm

Wow! Nice work cruisn!

What happened to your white WRX 4pot front calipers?

by **cruisn** » Mon Mar 25, 2013 12:41 am

dazzz168 wrote:Wow! Nice work cruisn!

What happened to your white WRX 4pot front calipers?

Cheers. White 4/2 pots still on the car. I'll move them on once I finish the Nissan ones.

by **cruisn** » Fri Mar 29, 2013 12:30 pm

Somethings not right in this picture......

3 pedals and an auto shifter?

Fitted the manual pedals and clutch cylinder. One less job for the conversion.

by **HoFF** » Fri Mar 29, 2013 12:41 pm

Lol that will confuse a few people

by **rooby** » Fri Mar 29, 2013 12:45 pm

That is odd. What is the deal with that, half-assed conversion?

by **Dropz** » Fri Mar 29, 2013 2:54 pm

Floor mats aren't made to fit so they don't sit nice.

Good idea, do what you can while you can, make it a nice easy job when it all arrives.

by **cruisn** » Fri Mar 29, 2013 4:12 pm

rooby wrote:That is odd. What is the deal with that, half-assed conversion?

Haha, as Karl said, do a bit now makes it quicker when I have to put the box in although I do have the all parts on hand ready to go.

Parents are going away for 2 weeks end of April so I will have two extra cars at my disposal. I'll do it then as if any unexpected issues arise, there's no issue with having the car off the road. :wink:

by **RX25SE** » Fri Mar 29, 2013 8:18 pm

Hahaha Mark.
I did the same when I switched the Ford over to manual, told all my mates it was a performance modification.

by **Kekotic** » Fri Mar 29, 2013 8:33 pm

RX25SE wrote:Hahaha Mark.
I did the same when I switched the Ford over to manual, told all my mates it was a performance modification.

Foot activated NOS button, bro

by **cruisn** » Sat Mar 30, 2013 5:16 pm

Front brackets finalised to mount the Nissan calipers.

Made a prototype out of nylon to check my measurements. Spot on. Running a 326mm Brembo front rotor.

I'll be making the final product this week.

by **bigBADbenny** » Sat Mar 30, 2013 11:17 pm

DIY rapid prototyping ftw :mrgreen:

by **bosc0** » Tue Apr 02, 2013 7:21 am

Left foot wristy pedal.

by **seanmau5** » Tue Apr 02, 2013 10:06 pm

cruisn wrote:Plastic and shitty tar removed.

Dynamat on the front doors to block all open area's, also section installed on outer door panel behind speaker = Massive improvement in bass from front speakers and decrease in road noise.

What did you use to remove that shit? Fook me it's messy as and I want to remove it when I re do my Dynamat

CRUISN's Gen2 JDM style surf wagon

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Re: Member Profile - CRUISN's work / surf hack.

Who is online