Learning View Snapshots \ Discussions

[alexeiwoody]

Hey guys, car just got dyno+road retuned by Matt (throttlehappy/kido), made 160kwaw on the mainland dyno, zero knock (so far so good ), fuel cons. looking good

Most importantly car feels smooth, and Matt had a chance to diagnose and workout any possible problems it could've had:

-logger still drops out on WOT - going to ground the gearbox and alternator better this week
-slight hesitation at around 5000rpm of the rpm needle - as it's rising on WOT it just stops at about 5000 holds for a second and keeps climbing - Matt says problem is most likely the spark plug leads/coils.

And a really big thank you to Matt (again ) for taking the time to work out all the kinks

LV after doing a few pulls and driving home etc

LearningView_SS_05-02-2013 10 41 34 pm.jpg (74.73 KiB) Viewed 3584 times

[Kekotic]

Good to hear things are looking better Alexei!

[alexeiwoody]

Thanks Kieran Next step - making a build thread....

[WheelieBin]

LearningView_SS_4-02-2013 5 15 29 PM.jpg (74.81 KiB) Viewed 3559 times

Post track day LV (literally taken sitting at the front gate of the track while Karl fixed a car). Stupidly I only thought about getting on track logs once, and then didn't think about it when the track was quiet, so didn't get any logs.

[Statts]

Flashed the revised tune, went for a ~15min drive including both 2nd and 3rd gear pulls (20km/h to redline). LV snapshot below, but looks a bit empty to me?

Above was directly after flashing my latest revision. A week and a bit and ~100km later, I have taken another snaphot......

[alexeiwoody]

Hey Statts, no point taking a shot straight after a reflash - it'll always read zero because you've just reset all the values to zero by reflashing.

The second LV is a good sign, maybe that -5.40 in the af ranges could be scaled a little better
Anyway go onto romraider site and read the walkthrough on learning view in the forum section...it's just a basic tool to check airflow ranges and knock. And cels. There's a whole heap more to a tune than what an LV records, although looks like your engine is knock free which is a good start

[Zaccy182]

Total noob, so genuinely after some feedback. Only mods being k&n panel filter and cat back with matts tune. This was pulled from my car this morning...

So just a bump on my previous post, update

After this LV the ECU was reset and since then Ive been driving around sensibly... Took another LV today and everything is fine: IAM has stayed on 1 and the table was showing all 0s. Cant remember what the airflow ranges were. I'm going to sorta drive it a bit harder and check the LV on Sunday to check for changes again.

[Kekotic]

You want to drive the car hard to check for knock. It's not going to knock if you baby it around.

[Zaccy182]

You want to drive the car hard to check for knock. It's not going to knock if you baby it around.

Yeah I know, just taking precautions... Ill be redoing the LV this Sunday and post that up. Fingers crossed knock doesn't occur...

[dr20t]

You want to drive the car hard to check for knock. It's not going to knock if you baby it around.

Yeah I know, just taking precautions... Ill be redoing the LV this Sunday and post that up. Fingers crossed knock doesn't occur...

Or if it does, that your knock correction strategy is sufficient enough and sensitive enough to deal with it

[KiDo_Tuning]

You want to drive the car hard to check for knock. It's not going to knock if you baby it around.

Yeah I know, just taking precautions... Ill be redoing the LV this Sunday and post that up. Fingers crossed knock doesn't occur...

Your factory tune had some big negative values and IAM was on 0.675 Dug out the LV to check last week, your ECU ID is rare plus they are date stamped so it made it easy to find

[bass_straitener]

You want to drive the car hard to check for knock. It's not going to knock if you baby it around.

Yeah I know, just taking precautions... Ill be redoing the LV this Sunday and post that up. Fingers crossed knock doesn't occur...

Your factory tune had some big negative values and IAM was on 0.675 Dug out the LV to check last week, your ECU ID is rare plus they are date stamped so it made it easy to find

Can we see that LV please.

[<GB>]

You want to drive the car hard to check for knock. It's not going to knock if you baby it around.

how is your learning veiw since the tune?

[Kekotic]

Matt took one directly after the dyno and a 20 min test drive and there was zero knock, he also said that of 2 hours on the dyno he heard absolutely no knock using the knock ears. He even increased the timing by 2 degrees to try find some knock and didn't get any, and then he returned the timing back.

I haven't had to drive the car since the dyno so have done no logs or LV, but I'll be taking an LV later today. An LV doesn't really give you that big of an insight anyway. The fact my car had zero knock on a dyno is more indicative than a learning view snapshot.

[WheelieBin]

Shav's LV from last night (yes, I still need to download the current version of LV):

LearningView_SS_7-02-2013 6 10 52 PM.jpg (74.83 KiB) Viewed 3431 times