Member Profile - JDGT05 Back in boosted wagon land 2015

[Maj3sticCr0w]

Sounds good but pics wont display?

Still not showing up?

Working now, looks awesome! Like you said any lower than that and car almost becomes unusable on street. Whats ur official ride height now? Also how much camber?

[JDGT05]

Sounds good but pics wont display?

Still not showing up?

Working now, looks awesome! Like you said any lower than that and car almost becomes unusable on street. Whats ur official ride height now? Also how much camber?

Heights about 120mm off the ground, not sure what the exact camber ended up being roughly 1.5 mark. Just made them sit nice. Really wanted the "hellaflush" look but after talking to them they said it doesn't work very well unless your cars on bags!

[Maj3sticCr0w]

Whats next on the cards?

[JDGT05]

Whats next on the cards?

Really want a unique boost gauge set up! But not sure where I go from here. Any ideas on what I should spend my money on next?

[Maj3sticCr0w]

Whats next on the cards?

Really want a unique boost gauge set up! But not sure where I go from here. Any ideas on what I should spend my money on next?

BlackJack.....and hookers!

But for your car you should get those private plates i rekon.

[JDGT05]

Whats next on the cards?

Really want a unique boost gauge set up! But not sure where I go from here. Any ideas on what I should spend my money on next?

BlackJack.....and hookers!

But for your car you should get those private plates i rekon.

Yeah that's true, I have to STI rubber lip on it's way so we shall see how thats doing! then maybe order some private plates!

[JDGT05]

Guys, this is a picture from a while ago, as you can see the ultrex front lip isn't perfectly straight. That was just the way it came, does anyone know of a way to straighten it out in line with the rest of the lip. It hasn't been scratched or bent, is there a way of perhaps fastening it better from behind without anyone noticing from the front?

[hamish_023]

Mine sits flat, but I did tek screw the middle bit so it isn't going to sag

[kennysti]

Whats next on the cards?

Really want a unique boost gauge set up! But not sure where I go from here. Any ideas on what I should spend my money on next?

I ordered a nice one from Phat quite some time ago now. If it turns up before the next cruise you should check it out. Minimal modifications and looks great IMO no drilling the dash either.

[Rome_BRZ]

Whats next on the cards?

Really want a unique boost gauge set up! But not sure where I go from here. Any ideas on what I should spend my money on next?

I ordered a nice one from Phat quite some time ago now. If it turns up before the next cruise you should check it out. Minimal modifications and looks great IMO no drilling the dash either.

Is that in the cubby hole? Or on the dash itself?

[JDGT05]

Whats next on the cards?

Really want a unique boost gauge set up! But not sure where I go from here. Any ideas on what I should spend my money on next?

I ordered a nice one from Phat quite some time ago now. If it turns up before the next cruise you should check it out. Minimal modifications and looks great IMO no drilling the dash either.

This is intriguing , I look forward to seeing this, mind spilling the beans on what it was all ready

[JDGT05]

Mine sits flat, but I did tek screw the middle bit so it isn't going to sag

Everything sits flush where it should all along the top of the lip, all bolts a tight in place. Just that particular part of the lip seems to be warped or bent slightly.

[Smithyy]

Mine sits flat, but I did tek screw the middle bit so it isn't going to sag

Everything sits flush where it should all along the top of the lip, all bolts a tight in place. Just that particular part of the lip seems to be warped or bent slightly.

Refund time :/

[Kekotic]

Did you drill the holes too close on the drivers side? Looks to be warping there near the fog?

[cruisn]

How have you attached the lip to the front bar in the middle area?

Ultrex say screws, but its a very small area of attachment using a screw into the bar alone and it will pull the bar down a bit. Panel clips are the go and what the oem STi lip is fitted with.