Member profile - MadmanSean

Show off what mods you've done to your car.

Member profile - MadmanSean

Postby MadmanSean » Mon Sep 12, 2016 9:02 am

G'Day guys been on here a wile now stalking and gathering ideas and thought it was about time i started my own thread :D

Car: Subaru Liberty GTB wagon 5EAT
Location: Vic Melbourne
Name: Sean

I've had the Liberty for almost 2 years now and have loved every minute of it!

Current Mods:
Stage 1 - 3/10/2016
Cosmic Racing Coilovers
DBA T2 front and Rear discs
MU NS400 Pads
Fumota oil drain valve
Kobe Silicon Inlet pipes
ID1000
Kobe 340lph pump
AWKW = FAST!

Stage 2 - 1/12/2016
Tuspeed 3 Port BCS
E85
Tomei FPR
Invidia Dump pipe
AWKW = EVEN FASTER!

Stage 3 - 8/3/2017
Mamba GTX3071r 56 Trim 0.64 A/R
AVO 3" Inlet
TGV Delete
Cusco Rear Diff Carrier
W2A Intercooler
PW Hotside piping
AWKW = Moderate Tune of ~16psi S# nice and responsive

Stage 3.5 - 4/4/2017
W2A System functioning correctly with 20L/min Pump
Empire 3" SS Catback
AWKW = F'ing Loud Awesomeness! -

Stage 4 - 24/4/2017
New Fuel Filter Installed
KIDO Tuned GTX3071r - I mode 12 psi, Sport 15psi, Sport # 18psi :D
AWKW = Soon to be Dyno'd
Dyno'd @ SPRINGY Performance 6/6/2017 - 211AWKW - Stock Airbox and cast UEL Headers

Stage 5 - 23/6/2017
DEAD....DEADER THAN DEAD....

As my car kreeps closer and closer to 200k k'ms i'm thinking i'm in need of some performance parts.
Not looking to go overboard as this is my Daily/Dog carrier but if i could get close to 250awkw on E85 i would be more than pleased.

Planned mods as of 28/11/2016:
EJ257 Short Block
Mahle Forged Pistons
ARP 2000 Headstuds
Cosworth Head Gaskets
Timing BElt Kit
11mm oil pump
Heads Reco'ed
Kelford Cams

Garret GTX3071r 56 trim 0.64 A/R
Process West silicone hotside pipe
Empire performance 3" SS Catback
TGV Delete (DIY)

Killer B oil pickup
Killer B Sump baffle

Invidia Dump Pipe
3 Port BCS
Kobe Inlet pipes - Now replaced with AVO 3" Inlet
Kobe 340 Pump
ID1000
CX Racing W2A Intercooler
Oil Catch Can

Hexmods Valve body mod
Tomei FPR
11mm Fuel rail adapter

Radium Fuel rails
Parallel Rail conversion
Brembo Calipers

316mm T2 Front Discs
326mm T2 Front Discs
Braided Brake lines
Project MU NS400 Pads
Innovate Wideband 02
BridgeStone RE003 225/40/18 (Stock GTB Rims)
Enkie RPF1 Black 18*8 +45
Adjustable Camber Tops

Whitline KDT906 Rear Diff mount bushes
Whitline KDT905 Rear Diff carrier bushes
CUSCO Rear Diff Carrier
CUSCO Front Strut Brace
CUSCO Rear Strut Brace
Coilovers

Whiteline KSR207 Front Steering - rack and pinion bushing
Whitline BSK014 F & R Sway Bar kit contains BSF30Z, BSR39Z, KLC139 & KLC144
Whiteline KTA124 Rear Control Arm - Front and Rear
Whitline Antilift kit
Whitline Strut quick release KSB790
Cusco Rear Lower Arm Brace.

Pitch Stop Mount
Air pump deletes

Tactrix Cable
STI Group N Engine Mounts
Paint and Wrap engine bay bits - Bling Spec


Her's some pics of how the car looks right now, enjoy and let me know what you think!
20150313_150029.jpg
GTBWagon1
20150313_150029.jpg (122.33 KiB) Viewed 63416 times

20151127_124235.jpg
GTB_Coilovers
20151127_124235.jpg (60.63 KiB) Viewed 63322 times

20151127_124005.jpg
GTB_EngineStock
20151127_124005.jpg (160.41 KiB) Viewed 63322 times

20150301_134302.jpg
GTBWagon2
20150301_134302.jpg (119.68 KiB) Viewed 63416 times
Last edited by MadmanSean on Wed Aug 10, 2022 7:58 am, edited 24 times in total.
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby bigBADbenny » Tue Sep 13, 2016 6:32 pm

Nice one, love a white wagon :)
Just make sure your planned power level suits your AT, or look into some mods to the box to suit that power...
User avatar
bigBADbenny
 
Posts: 10420
Joined: Tue Oct 04, 2011 6:36 pm
Location: Collingwood, Melbourne
Car: MY07 GT-B 6MT OBP Wagon
Real name: Ben Richards
Profile URL: http://tinyurl.com/agvbzop

Re: Member profile - MadmanSean

Postby MadmanSean » Mon Sep 26, 2016 1:23 pm

bigBADbenny wrote:Nice one, love a white wagon :)
Just make sure your planned power level suits your AT, or look into some mods to the box to suit that power...


Hi BBB, Thanks for the advice! I got in contact with Kewish Auto who quoted me a rough price over the phone that is pretty reasonable, so might get a valve body mod and clutch packs done before Christmas ;)

Bit of an Update also:

Got my Slotted rotors and Pads installed!
20160924_110500.jpg
GTB_T2DISCSandMUPads
20160924_110500.jpg (58.56 KiB) Viewed 63322 times


Installed a Kobe 340lph Pump!
20160925_112526.jpg
Kobe 340lph Pump
20160925_112526.jpg (90.32 KiB) Viewed 63630 times


And i'm in the process of installing ID1000's and Kobe Silicone Inlet pipes, ran out of time Sunday to complete the job... Hopefully tonight it'll be up and running!

Also washed the beast, Looks Schmicko!
20160924_145659.jpg
GTB Wagon3
20160924_145659.jpg (139.59 KiB) Viewed 63322 times

20160924_145734.jpg
GTBWagon4
20160924_145734.jpg (138.9 KiB) Viewed 63416 times
Last edited by MadmanSean on Mon Nov 14, 2016 7:18 am, edited 2 times in total.
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby bigBADbenny » Mon Sep 26, 2016 4:30 pm

That's great! Who is on the tuning duties?
Fairly sure those mods need a tune like, immediately, failing that, really poodle it in "i" mode if at all :)
User avatar
bigBADbenny
 
Posts: 10420
Joined: Tue Oct 04, 2011 6:36 pm
Location: Collingwood, Melbourne
Car: MY07 GT-B 6MT OBP Wagon
Real name: Ben Richards
Profile URL: http://tinyurl.com/agvbzop

Re: Member profile - MadmanSean

Postby MadmanSean » Tue Sep 27, 2016 9:22 am

bigBADbenny wrote:That's great! Who is on the tuning duties?
Fairly sure those mods need a tune like, immediately, failing that, really poodle it in "i" mode if at all :)


Managed to get the car back together last night despite the rain... Stupid Melbourne weather :lol:

I got a tactrix cable and scaled the injectors myself it runs but im not game enough to go high in revs just yet, still poodled it in "i" mode anyways :lol:
Hoping Matt (Kido Tunes) can fit me in for his Melbourne visit :D
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby bigBADbenny » Tue Sep 27, 2016 1:26 pm

Baller!
User avatar
bigBADbenny
 
Posts: 10420
Joined: Tue Oct 04, 2011 6:36 pm
Location: Collingwood, Melbourne
Car: MY07 GT-B 6MT OBP Wagon
Real name: Ben Richards
Profile URL: http://tinyurl.com/agvbzop

Re: Member profile - MadmanSean

Postby gtbsti » Tue Sep 27, 2016 7:52 pm

sits very nicely mate
User avatar
gtbsti
 
Posts: 142
Joined: Thu Oct 04, 2012 7:21 pm
Car: MY08 GT Spec.B Tuned By STi Wagon
Profile URL: JDM Wagonist

Re: Member profile - MadmanSean

Postby MadmanSean » Wed Sep 28, 2016 9:07 am

bigBADbenny wrote:Baller!


You know it! :wink:


gtbsti wrote:sits very nicely mate


Thanks! It's enough stance for me Haha


Booked in with Matt (Kido) for the 3rd Oct, Soo keen to get some tuning done! :D
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby MadmanSean » Thu Sep 29, 2016 9:11 am

Happy snaps from my car mod adventures Haha
20160927_200314.jpg
GTBWagon5
20160927_200314.jpg (62.45 KiB) Viewed 63527 times
20160918_161111.jpg
GTBWagon6
20160918_161111.jpg (51.04 KiB) Viewed 63527 times

Decided to check out the tune that was already in the car using RomRaider. I think it may have already been modified as the target boost table hits a maximum of 17.6psi?? I thought the maximum on stock tune (Subaru factory) was 13.5psi or there abouts...
TargetBoostTable.JPG
TargetBoostTable
TargetBoostTable.JPG (88.92 KiB) Viewed 63527 times

The DBW tables also look to have been modified;
DBWThrottle.JPG
DBWTable
DBWThrottle.JPG (115.61 KiB) Viewed 63527 times

Hmm very interesting... :shock:

Also i drove the car today and have Error code P0108 Map Senser high showing up... it comes up straight after flashing a rom to the ecu without even starting the engine...
Any one have any suggestions on how to troubleshoot this, is it related to having a vacuum leak somewhere?
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby bigBADbenny » Thu Sep 29, 2016 10:55 am

Scroll down for the general diagnostic procedure...
https://www.obd-codes.com/p0108

Some of the vac hoses eg ebcs/boost controller & purge control, at the front of the inlet mani can get brittle and break, also the one at the nipple on the pass side inlet mani for the fpr iirc.

Check the turbo vac lines are around the right way too, if those were messed with ;)

Use small zipties on all connections whilst you're at it!



...
Last edited by bigBADbenny on Thu Sep 29, 2016 1:46 pm, edited 1 time in total.
User avatar
bigBADbenny
 
Posts: 10420
Joined: Tue Oct 04, 2011 6:36 pm
Location: Collingwood, Melbourne
Car: MY07 GT-B 6MT OBP Wagon
Real name: Ben Richards
Profile URL: http://tinyurl.com/agvbzop

Re: Member profile - MadmanSean

Postby MadmanSean » Thu Sep 29, 2016 1:39 pm

bigBADbenny wrote:Scroll down for the general diagnostic procedure...
https://www.obd-codes.com/p0108
Some of the vac hoses eg ebcs/boost controller & purge control, at the front of the inlet mani can get brittle and break, also the one at the nipple on the pass side inlet mani for the fpr iirc.
Check the turbo vac lines are around the right way too, if those were messed with ;)
Use small zipties on all connections whilst you're at it!
...

Thanks BBB!
I checked the MAP sensor following those instructions and the P0108 Fault code went away :D
However i also found that Ive forgotten to connect (Or it has popped off) a hose and sensor connector that are located under the wiring harness that runs at the back of the inlet mani, just near the turbo. Might be a coolant line... Lucky i brought my tools to work Haha :)
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby alexeiwoody » Thu Sep 29, 2016 1:41 pm

MadmanSean wrote:Happy snaps from my car mod adventures Haha
20160927_200314.jpg
20160918_161111.jpg

Decided to check out the tune that was already in the car using RomRaider. I think it may have already been modified as the target boost table hits a maximum of 17.6psi?? I thought the maximum on stock tune (Subaru factory) was 13.5psi or there abouts...
TargetBoostTable.JPG

The DBW tables also look to have been modified;
DBWThrottle.JPG

Hmm very interesting... :shock:

Also i drove the car today and have Error code P0108 Map Senser high showing up... it comes up straight after flashing a rom to the ecu without even starting the engine...
Any one have any suggestions on how to troubleshoot this, is it related to having a vacuum leak somewhere?


Even without looking up the exact model, I'm 99% sure those are stock tables... both tables have the exact shape of stock tables. If someone did alter them, they put in a lot of effort to not make them any better or worse in any way.... :lol:

What makes you say the DBW has been altered?
Running no. of weeks without breaking something in the lib: 0
No. of things still to fix in in the lib: 97
User avatar
alexeiwoody
 
Posts: 1900
Joined: Thu Jul 12, 2012 11:47 pm
Location: Melbourne
Car: MY07 LibGT 5EAT
Real name: Alexei

Re: Member profile - MadmanSean

Postby MadmanSean » Thu Sep 29, 2016 2:13 pm

alexeiwoody wrote:Even without looking up the exact model, I'm 99% sure those are stock tables... both tables have the exact shape of stock tables. If someone did alter them, they put in a lot of effort to not make them any better or worse in any way.... :lol:

What makes you say the DBW has been altered?

Okay then, I'm not entirely sure what it should or shouldn't look like as im a bit of noob with Subies
Here's what the tables look like in a stock Rom i got from RomRaider Forum.
Boost.JPG
StockMapBoost
Boost.JPG (87.57 KiB) Viewed 63506 times

Boost is around 13.5psi??
DBW.JPG
StockRomDBW
DBW.JPG (119.07 KiB) Viewed 63506 times
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Re: Member profile - MadmanSean

Postby alexeiwoody » Thu Sep 29, 2016 3:38 pm

Those are not the tables from your car.

Possibly from a postFl tbSti (notice the horrible 2D DBW table. No Liberty came like that from factory, while the tbSti was "enhanced" at Sti Australia).

That boost table you posted just now, also doesn't look much like stock Subaru work. So quite possibly it's a ROM from a tbSti or someone who thought they had a stock ROM, but it was actually previously modified by a 2 year old.

Compare to any WRX or Sti tune and you'll see much more similarity to what you pulled out of your car.

That's a clue as to why many a postFl tbSti have gone through an engine or two on an otherwise stock car. :oops: :angry2:
Running no. of weeks without breaking something in the lib: 0
No. of things still to fix in in the lib: 97
User avatar
alexeiwoody
 
Posts: 1900
Joined: Thu Jul 12, 2012 11:47 pm
Location: Melbourne
Car: MY07 LibGT 5EAT
Real name: Alexei

Re: Member profile - MadmanSean

Postby MadmanSean » Thu Sep 29, 2016 4:01 pm

alexeiwoody wrote:Those are not the tables from your car.

Possibly from a postFl tbSti (notice the horrible 2D DBW table. No Liberty came like that from factory, while the tbSti was "enhanced" at Sti Australia).

That boost table you posted just now, also doesn't look much like stock Subaru work. So quite possibly it's a ROM from a tbSti or someone who thought they had a stock ROM, but it was actually previously modified by a 2 year old.

Compare to any WRX or Sti tune and you'll see much more similarity to what you pulled out of your car.

That's a clue as to why many a postFl tbSti have gone through an engine or two on an otherwise stock car. :oops: :angry2:


Thanks for the clarification Alexei. Please note i have pressed the "Delete" Key and the file no longer exists :lol:
Subaru ECU Unbricking, Unlocking and Bench Flashing/Recovery service! Check out SICK CHIPS @ https://www.facebook.com/SickChips/
http://forum.liberty.asn.au/viewtopic.php?f=56&t=35489
If you'd like to say thank you feel free to Buy me a coffee https://www.buymeacoffee.com/sickchips
User avatar
MadmanSean
 
Posts: 188
Joined: Tue Mar 17, 2015 6:27 pm
Location: Melbourne
Car: 2007 Libert GT SpecB wagon
Real name: Sean
Profile URL: viewtopic.php?f=10&t=33793

Next

Return to Post your mods

Who is online

Users browsing this forum: Google [Bot] and 6 guests