Trialing pedders lowering springs

[todda189]

Hey guys I will b trialing the pedders lowering springs in my 3.0rb
Tomorrow. Apparently I will drop an extra 15mm compared to the
Kings I'm already running .
Anybody else running these ?

[Q]

Hey guys I will b trialing the pedders lowering springs in my 3.0rb
Tomorrow. Apparently I will drop an extra 15mm compared to the
Kings I'm already running .
Anybody else running these ?

15mm lower than the King springs on 20" rims

I doubt anyone has tried that combo but let us know how you go...

[Arith]

Are you trialing a new line of Pedders? Beacuse I'm sure there have been people on this forum and people not of this forum who have fitted Pedders on their Libertys before (myself included, on my MY05 GT). I did run them with 19" wheels and it wasn't too bad as I stuck mainly to street use.

I actually wanted the front a bit lower at one point, and tried to to fit King springs up front as on the data sheet Kings were lower. However there's something wrong with King's QA as the springs they sent out were higher than the Pedders so I went back to the Pedders.

[todda189]

pedders were right it has dropped it by an extra 15mm compared to the kings and a much better ride aswell!!
they told me to measure from the bottom of my 20" wheel to the guard and their springs should sit at 625mm which it has , sits alot better now

[Greenman]

You may find the springs will smake the car sit a bit more level...in the rear.
Great Choice.

[jslayz]

Please pop up a pic from side on.
Keen to see how it sits....

Cheers

J

[Pyramidrocker]

I have the Kings aswell. I'm happy with the feel of them, BUT! Not happy with the asthetics.
Front dropped the 30mm i was after but the back only dropped 5mm.It now sits a little un-even.
I should've went for the Pedders, i guess i got what i paid for with the Kings.

[todda189]

correct it does sit even , on y thing is i need to roll my guards as im running 245 tyres wich are abit wider then standard lol!!
i will get a pic of how it sits and ill make the phone call to get the different ride heights for the different size wheels

[todda189]

I have the Kings aswell. I'm happy with the feel of them, BUT! Not happy with the asthetics.
Front dropped the 30mm i was after but the back only dropped 5mm.It now sits a little un-even.
I should've went for the Pedders, i guess i got what i paid for with the Kings.

yeah the kings feel great but didnt serve the purpose in which i bought them for !!
i recommend u change to the pedders , great thing is they sell at a reasonable price aswell

[Murch]

+2 on the side on picks.

I've just put a new set of bilstein struts and phat sepcials tein s.tech springs on my MY05 GT sedan - the car still a little higher at the front, but I'm hoping it settles a little. I'm keen to see how the pedders look.

The tein/billies combo is a great ride though.

[todda189]

hey guys heres the pics
hope they help!!

side on

side.jpg (62.6 KiB) Viewed 3548 times

side on 2

side 2.jpg (64.04 KiB) Viewed 3548 times

front wheel

frt wheel.jpg (75.31 KiB) Viewed 3548 times

rear wheel

rear.jpg (71.41 KiB) Viewed 3548 times

measurement

DSCF0150.JPG (63.08 KiB) Viewed 3548 times

[Murch]

That sits perfect. Most of the GT's I've seen usual sit higher at the front (like mine on teins).

Would the front of a 3.0rb sit a little lower at the front due to the heavier engine? I'm wondering if it might be worth me getting pedders springs to replace my teins in the front end. But wondering if due to a ligher 2.0t engine it would still sit higher (than the pics above).

Nice ride Todda

[todda189]

thnx mate
i did think about the heavier engine but im not to sure , i guess the only way to find out is give it a go!!
what size rims do u have ?

[Murch]

thnx mate
i did think about the heavier engine but im not to sure , i guess the only way to find out is give it a go!!
what size rims do u have ?

currently just have the stock 17's but will be putting on some 18" rota gravels - tbSti look-a-likes. I've considered 19's but can't find any I like...plus trying to keep it modest.

I'll give my teins a few weeks to settle in and see how it looks with bigger wheels, but may consider trying on some pedders.

[todda189]

thnx mate
i did think about the heavier engine but im not to sure , i guess the only way to find out is give it a go!!
what size rims do u have ?

currently just have the stock 17's but will be putting on some 18" rota gravels - tbSti look-a-likes. I've considered 19's but can't find any I like...plus trying to keep it modest.

I'll give my teins a few weeks to settle in and see how it looks with bigger wheels, but may consider trying on some pedders.

with 17's if u measure from the bottom of the rim to the bottom of the guard , the pedders springs will sit at 590mm and thats listed for the 4 cylinder engine
with my 20's they said measure from the bottom of the rim to the guard and it should sit at 625mm and its spot on