Need heads bolted back onto the block, brisbane

[vadercelica]

just reconditioned heads on my 05 liberty gt, need them bolted back onto the head, bought new gaskets for head and new bolts, in brisbane, anyone recommended for the EJ20T engine???

[kiahatsiu]

Hi,
John French at Woolloongabba, or if you feel like travelling, A&M Performance up Noosa way.

May I ask why you had your heads recoed?

[50BIE]

Depends where you are in Brisbane mate

Quality work AM Auto @ Noosaville & John French are the picks of Subaru specialists, the later make sure you have a pocket full of money though!
others that can do it are the guys at Subi Evolution @ Brendale and PMS @ Slacks Creek http://www.pms.net.au/

cheers
Steve

[vadercelica]

located in brisbane southside so dont really want to go to noosa etc...

heads were reconditioned whilst new timing belt is going in etc for better flow and bit more power

[kiahatsiu]

Make sure you have your tensioner bolts checked or replaced. They just snap otherwise apparently.

[Breeze91]

Hah, I just had my heads done too. What did you have done in the reco. I had my short side radii smoothed and a 7 angle (yep 7) valve job. Can't wait to see how it goes with the new lightened solid flywheel as well. Valves are stock size. I have the 206kw jap spec legacy and it already went very well I am hoping it'll still run like a clock.

What sort of b1tch were those bloody exhaust sheild bolts to get off when pulling the motor? I couldn't believe them!

Mine has done 130kms and the insides of the bores still look like new with the original cross hatching all the way down! How did yours look?

Did you get Sub bolts, arp or permaseal?

Cheers

[vadercelica]

Hah, I just had my heads done too. What did you have done in the reco. I had my short side radii smoothed and a 7 angle (yep 7) valve job. Can't wait to see how it goes with the new lightened solid flywheel as well. Valves are stock size. I have the 206kw jap spec legacy and it already went very well I am hoping it'll still run like a clock.

What sort of b1tch were those bloody exhaust sheild bolts to get off when pulling the motor? I couldn't believe them!

Mine has done 130kms and the insides of the bores still look like new with the original cross hatching all the way down! How did yours look?

Did you get Sub bolts, arp or permaseal?

Cheers

hey man, my dad took off the heads, and it was a mission and a half he said, got the whole heads recond with new stainless steel valves, my engine has 50 on the clock haha , i havnt bought new bolts yet (you mean the tension bolts).... do you live in brisbane? or your overseas???? whos bolting the heads back onto your block for you?

[Breeze91]

I was talking head bolts. You have to replace them. There are a variety of options. I got the permaseal ones but they looked like $1 galbv bolts you get from a bunnings store. So I took them back and ended up getting stock bolts.

I am in Adelaide and Tony Knight (Knight Engines) did my heads.

The AVCS cam pulleys are a mongrel without a rattle gun. Your old man did very well to get them off.

I have taken the opportunity to do everything on the car while the motor is out. Diff, box, pwr steering and brake fluid replacement, new pads all round, new clutch, new flywheel, timing belt, tensioner and idlers, fan belts, coolant, oil and filters. Overall a pretty expensive service. Should be pretty right for another 100K now!

[subnub]

Not sure if you have this sorted already but if not, you could give Dan Kent at Elite Racing Developments a go, he's in Stapylton/Yatala and a lot of people in the Skyline scene regard him as a good honest bloke who knows his stuff.

He's pretty much built whole cars for friends, including ~600whp time attack cars. IMHO he's worth a call, I reckon he'd be able to help you out Tell him Revhead referred you... he might look after you, he might double the price

2 / 7 Angel Road
Stapylton
Queensland
4207

Telephone: 07 3807 2789

[SMI77]

The Serge, Sergio La Monaca, ph 0411 094350 is a Subaru spannerman guru.