club.liberty.asn.au

I just recently had 18 inch wheels with low profiles put on my car
The car hasn't been lowered, but when i have at least 2 people in the back seat or 1 fat person in the back seat the wheels scrape like hell!!!!!

is there a way i can fix this issue?

talev788 wrote:I just recently had 18 inch wheels with low profiles put on my car
The car hasn't been lowered, but when i have at least 2 people in the back seat or 1 fat person in the back seat the wheels scrape like hell!!!!!

is there a way i can fix this issue?

Pending the offset of the wheels and the tyre size, I'd suggest you probably need to roll the rear guards. Generally around $50 per corner.

Hotwire wrote:

talev788 wrote:I just recently had 18 inch wheels with low profiles put on my car
The car hasn't been lowered, but when i have at least 2 people in the back seat or 1 fat person in the back seat the wheels scrape like hell!!!!!

is there a way i can fix this issue?

Pending the offset of the wheels and the tyre size, I'd suggest you probably need to roll the rear guards. Generally around $50 per corner.

+1. If you haven't even lowered yet you are probably being over optimistic with your wheel /tyre width and offset.

MY02 => seven years old. Rear springs may be sagging.
what exactly was the original tyre size, and what you have on now?

Ric wrote:MY02 => seven years old. Rear springs may be sagging.
what exactly was the original tyre size, and what you have on now?

original size was the 16 inch stockies

i now hav 18 inch osaka vertecs with low profiles

talev788 wrote:

Ric wrote:MY02 => seven years old. Rear springs may be sagging.
what exactly was the original tyre size, and what you have on now?

original size was the 16 inch stockies

i now hav 18 inch osaka vertecs with low profiles

If the offset is less than + 50 you will need to roll the lip on the rear guards. + 55 you do not. I run +55 and have not problem

talev788 wrote:

Ric wrote:MY02 => seven years old. Rear springs may be sagging.
what exactly was the original tyre size, and what you have on now?

original size was the 16 inch stockies

i now hav 18 inch osaka vertecs with low profiles

You've just told me the wheel size. I asked for the exact tyre sizes. e.g. 215/45R18

Ric wrote:

talev788 wrote:

Ric wrote:MY02 => seven years old. Rear springs may be sagging.
what exactly was the original tyre size, and what you have on now?

original size was the 16 inch stockies

i now hav 18 inch osaka vertecs with low profiles

You've just told me the wheel size. I asked for the exact tyre sizes. e.g. 215/45R18

oh sorry dude wasnt paying attention, i'll go check it out wen i get a chance

Ric wrote:

talev788 wrote:

Ric wrote:MY02 => seven years old. Rear springs may be sagging.
what exactly was the original tyre size, and what you have on now?

original size was the 16 inch stockies

i now hav 18 inch osaka vertecs with low profiles

You've just told me the wheel size. I asked for the exact tyre sizes. e.g. 215/45R18

Stock Tyre is 205/50/16
i am running 215/35/18 and my car is lowered and i have no issues with scrubbing

RX_MY02 wrote:Stock Tyre is 205/50/16
i am running 215/35/18 and my car is lowered and i have no issues with scrubbing

205/50/16 => 611.4mm diameter
215/35/18 => 607.7mm diameter

So you've actually gone 0.6% smaller. See http://www.miata.net/garage/tirecalc.html

Ric wrote:

RX_MY02 wrote:Stock Tyre is 205/50/16
i am running 215/35/18 and my car is lowered and i have no issues with scrubbing

205/50/16 => 611.4mm diameter
215/35/18 => 607.7mm diameter

So you've actually gone 0.6% smaller. See http://www.miata.net/garage/tirecalc.html

Sweet site - Thanks for it Ric.

OK Just looked up the Osaka Vertec wheels, and the 18x7.5 size is listed as follows:
18x7.5 5/100, 5/108, 5/114.3 35mm - 45mm MATT BLACK

SO I'd say you have 18x7.5 with a 45mm offset. This sounds like it may be a bit to agressive for a Gen III, so Rolling the guards is probably going to be the only way you can fix this.

What width tyre are you running?

Ric wrote:

RX_MY02 wrote:Stock Tyre is 205/50/16
i am running 215/35/18 and my car is lowered and i have no issues with scrubbing

205/50/16 => 611.4mm diameter
215/35/18 => 607.7mm diameter

So you've actually gone 0.6% smaller. See http://www.miata.net/garage/tirecalc.html

Yeah i know, ive used that site before.

Ideally id like 225/35/18 but 215s are cheaper and easier to get