Page 1 of 1
Help please!!!! Temporary maps to drive car to tuner
Posted:
Wed May 03, 2017 3:02 pmby TRVIING
Hey guys,
I just put some mods on my liberty gt spec B. Does anyone have a map so that I can put on my car to drive to my tuner? The tow fee is hectic. Thanks in advace
Here is the mods list:
vf52 turbo
avo turbo back exhaust
grimmspeed 3 ports solenoid
hyperflow CAI
AVO TMIC
AVO BOV
Re: Help please!!!! Temporary maps to drive car to tuner
Posted:
Wed May 03, 2017 4:08 pmby Surge
Can you use a bit of vac line to connect the compressor housing to the BPV, eliminating the BCS for now so that you only run wastegate pressure ?
That might get you there just fine. Maybe stay light on the throttle.
Otherwise do have a tactrix cable and ecuflash?
Got a copy of your rom?
I'd be happy to put together a temp map if nobody else has a safe one they can share.
Re: Help please!!!! Temporary maps to drive car to tuner
Posted:
Wed May 03, 2017 4:11 pmby TRVIING
Thanks mate. I have the cable and software. I will pull the map out soon and send it to you
Re: Help please!!!! Temporary maps to drive car to tuner
Posted:
Thu May 04, 2017 10:46 amby TRVIING
Surge wrote:Can you use a bit of vac line to connect the compressor housing to the BPV, eliminating the BCS for now so that you only run wastegate pressure ?
That might get you there just fine. Maybe stay light on the throttle.
Otherwise do have a tactrix cable and ecuflash?
Got a copy of your rom?
I'd be happy to put together a temp map if nobody else has a safe one they can share.
@Surge here is the ROM of my car. Please change it back to .hex file Thanks heaps mate
Re: Help please!!!! Temporary maps to drive car to tuner
Posted:
Thu May 04, 2017 8:51 pmby Surge
So I have attached the modified map.
This is as safe as I could make it, changes are:
* Initial WGDC set to 0, to run only wastegate pressure.
* Boost Control Disable is increased to 0.8 / 0.9.
* Primary Open Loop Fueling - everything below 11.2 set at 11.2.
* Failsafe Fueling is slightly richer in the high load area.
* The switch to the Failsafe table set to happen at 0.8 IAM.
* Base timing is lower in the WOT areas by about 4 degrees.
* Knock Correction Advance Max has been divided by 4.
* Initial IAM is 1.0. So no need to wait for IAM to go to 1.0 after a reflash.
After flashing, drive around staying out of boost if possible. Keep an eye on learningview after a test drive.
Re: Help please!!!! Temporary maps to drive car to tuner
Posted:
Fri May 05, 2017 12:22 amby TRVIING
Surge wrote:So I have attached the modified map.
This is as safe as I could make it, changes are:
* Initial WGDC set to 0, to run only wastegate pressure.
* Boost Control Disable is increased to 0.8 / 0.9.
* Primary Open Loop Fueling - everything below 11.2 set at 11.2.
* Failsafe Fueling is slightly richer in the high load area.
* The switch to the Failsafe table set to happen at 0.8 IAM.
* Base timing is lower in the WOT areas by about 4 degrees.
* Knock Correction Advance Max has been divided by 4.
* Initial IAM is 1.0. So no need to wait for IAM to go to 1.0 after a reflash.
After flashing, drive around staying out of boost if possible. Keep an eye on learningview after a test drive.
Thank you sir. What a legend !!
