Help please!!!! Temporary maps to drive car to tuner

Tuning, diagnostics, ECUs and associated bits and bytes
Forum rules
Please respect copyright.
Do not post full copies of professionally tuned roms!

Help please!!!! Temporary maps to drive car to tuner

Postby TRVIING » Wed May 03, 2017 3:02 pm

Hey guys,

I just put some mods on my liberty gt spec B. Does anyone have a map so that I can put on my car to drive to my tuner? The tow fee is hectic. Thanks in advace

Here is the mods list:

vf52 turbo
avo turbo back exhaust
grimmspeed 3 ports solenoid
hyperflow CAI
AVO TMIC
AVO BOV

:clapping:
TRVIING
 
Posts: 14
Joined: Wed Feb 08, 2017 11:54 pm
Location: Melbourne, Victoria
Car: Liberty GT Spec B 6 Speed
Real name: TRVIING

Re: Help please!!!! Temporary maps to drive car to tuner

Postby Surge » Wed May 03, 2017 4:08 pm

Can you use a bit of vac line to connect the compressor housing to the BPV, eliminating the BCS for now so that you only run wastegate pressure ?

That might get you there just fine. Maybe stay light on the throttle.

Otherwise do have a tactrix cable and ecuflash?
Got a copy of your rom?

I'd be happy to put together a temp map if nobody else has a safe one they can share.
User avatar
Surge
 
Posts: 822
Joined: Sat Dec 08, 2012 1:28 pm
Location: ACT
Car: 2010 lib GT 5eat

Re: Help please!!!! Temporary maps to drive car to tuner

Postby TRVIING » Wed May 03, 2017 4:11 pm

Thanks mate. I have the cable and software. I will pull the map out soon and send it to you
TRVIING
 
Posts: 14
Joined: Wed Feb 08, 2017 11:54 pm
Location: Melbourne, Victoria
Car: Liberty GT Spec B 6 Speed
Real name: TRVIING

Re: Help please!!!! Temporary maps to drive car to tuner

Postby TRVIING » Thu May 04, 2017 10:46 am

Surge wrote:Can you use a bit of vac line to connect the compressor housing to the BPV, eliminating the BCS for now so that you only run wastegate pressure ?

That might get you there just fine. Maybe stay light on the throttle.

Otherwise do have a tactrix cable and ecuflash?
Got a copy of your rom?

I'd be happy to put together a temp map if nobody else has a safe one they can share.


@Surge here is the ROM of my car. Please change it back to .hex file Thanks heaps mate
Attachments
Liberty GTB.pdf
Base ROM
(1 MiB) Downloaded 238 times
TRVIING
 
Posts: 14
Joined: Wed Feb 08, 2017 11:54 pm
Location: Melbourne, Victoria
Car: Liberty GT Spec B 6 Speed
Real name: TRVIING

Re: Help please!!!! Temporary maps to drive car to tuner

Postby Surge » Thu May 04, 2017 8:51 pm

So I have attached the modified map.

This is as safe as I could make it, changes are:


* Initial WGDC set to 0, to run only wastegate pressure.

* Boost Control Disable is increased to 0.8 / 0.9.

* Primary Open Loop Fueling - everything below 11.2 set at 11.2.

* Failsafe Fueling is slightly richer in the high load area.

* The switch to the Failsafe table set to happen at 0.8 IAM.

* Base timing is lower in the WOT areas by about 4 degrees.

* Knock Correction Advance Max has been divided by 4.

* Initial IAM is 1.0. So no need to wait for IAM to go to 1.0 after a reflash.


After flashing, drive around staying out of boost if possible. Keep an eye on learningview after a test drive.
Attachments
Safemap.pdf
(1 MiB) Downloaded 234 times
User avatar
Surge
 
Posts: 822
Joined: Sat Dec 08, 2012 1:28 pm
Location: ACT
Car: 2010 lib GT 5eat

Re: Help please!!!! Temporary maps to drive car to tuner

Postby TRVIING » Fri May 05, 2017 12:22 am

Surge wrote:So I have attached the modified map.

This is as safe as I could make it, changes are:


* Initial WGDC set to 0, to run only wastegate pressure.

* Boost Control Disable is increased to 0.8 / 0.9.

* Primary Open Loop Fueling - everything below 11.2 set at 11.2.

* Failsafe Fueling is slightly richer in the high load area.

* The switch to the Failsafe table set to happen at 0.8 IAM.

* Base timing is lower in the WOT areas by about 4 degrees.

* Knock Correction Advance Max has been divided by 4.

* Initial IAM is 1.0. So no need to wait for IAM to go to 1.0 after a reflash.


After flashing, drive around staying out of boost if possible. Keep an eye on learningview after a test drive.


Thank you sir. What a legend !! :good:
TRVIING
 
Posts: 14
Joined: Wed Feb 08, 2017 11:54 pm
Location: Melbourne, Victoria
Car: Liberty GT Spec B 6 Speed
Real name: TRVIING


Return to Tuning

Who is online

Users browsing this forum: No registered users and 10 guests