Tru-Fit 3D Mats Gen4,5, BRZ direct from the distributor.

by **cruisn** » Mon Jan 07, 2013 6:55 pm

Pfffft, your installation skills are weak young padowan.

Once I machine and show my locating tab, the world will be mine! Mine I tell you!

by **sjm69** » Mon Jan 07, 2013 6:56 pm

Thanks will pick up the supplies for the install tomorrow

by **ferret89** » Mon Jan 07, 2013 8:01 pm

chaotic2050 wrote:
sjm69 wrote:
ferret89 wrote:Received my set today, it was a complex installation but I managed to install them by myself. Looks great

Did you have to go to bunnings to buy any tools for this complex installation ??
If so please let us know that they where and a walk through with lots of photos of this complex installation
Many thanks

It took me about 6 hours to install them.
I had to take out the entire floor carpet and all the seats, then I had to battle Cthulhu to lay claim to the section the mats needed to be installed it.
I also used about 4 litres of glue and about 17 nails.

Hope this helps.

I did have to go to bunnings. I used exterior wood screws to attach the mats to some steel brackets then welded those to the chassis and the seats. Then used some liquid nails on any exposed areas to ensure that they were firmly attached.
I think it'll hold up for a while, if not I'll have to consult some sort of engineer for a better solution.

Good luck with it all, during the install I downed 6 V cans and 4 mothers to keep my strength up. I advise you do the same.

by **sjm69** » Mon Jan 07, 2013 8:09 pm

Nope........ this is all getting to hard for me , remove carpet , welding ,screwing and gluing
Benny can I send mine back and get a refund ,ill go to Kmart and just buy the $8 ones that you just unpack and lay on the carpet , much much easier and quicker to install less chance of me stuffing it up
Thanks

by **SH30RB** » Mon Jan 07, 2013 8:20 pm

ferret89 wrote:Good luck with it all, during the install I downed 6 V cans and 4 mothers to keep my strength up. I advise you do the same.

Just to clarify, were the V cans the 250ml or 500ml variations? or was it the Limited Edition Halo 4 760ml variety cans?

by **SH30RB** » Mon Jan 07, 2013 8:21 pm

sjm69 wrote:ill go to Kmart and just buy the $8 ones that you just unpack and lay on the carpet

mine were $5 when i purchased a set in 2011

by **sjm69** » Mon Jan 07, 2013 8:31 pm

Inflation. my son

by **bigBADbenny** » Mon Jan 07, 2013 8:44 pm

I ate the clag and self crucified wit de tappers...

by **bosc0** » Tue Jan 08, 2013 6:31 am

Who is responsible for the mess in this thread? What a disgrace.

Benny, maybe i come see you this afternoon... yes.

by **sjm69** » Tue Jan 08, 2013 7:05 am

bigBADbenny wrote:I ate the clag and self crucified wit de tappers...

by **bigBADbenny** » Tue Jan 08, 2013 7:38 am

bosc0 wrote: this afternoon... yes.

PM u!

by **bigBADbenny** » Tue Jan 08, 2013 9:48 am

Posted today: Simon Liang

by **LostyJai** » Tue Jan 08, 2013 10:16 am

Thanks Ben!!!

by **HoFF** » Tue Jan 08, 2013 3:56 pm

My clutch pedal started grabbing the mat today. Not happy.

What would be the best method for cutting these?

by **zch91** » Tue Jan 08, 2013 4:11 pm

HoFF wrote:My clutch pedal started grabbing the mat today. Not happy.

What would be the best method for cutting these?

2nd post from the top, on the previous page (9) explains this.

Tru-Fit 3D Mats Gen4,5, BRZ direct from the distributor.

Re: Group Buy: Gen4 3D Floor Mats :-)

Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Group Buy: Gen4 3D Floor Mats :-)

Re: Group Buy: Gen4 3D Floor Mats :-)

Who is online