2011 Liberty HID changing to 100W LED

Here's where you can ask for suggestions what MODs you should consider. Let the experts tell you what you should add.

2011 Liberty HID changing to 100W LED

Postby evilsim » Sat Nov 07, 2020 7:36 pm

Hello Liberty folks !

I have been unimpressed with the Xenon bulbs in my '11 Liberty GT. I have replaced the bulbs with new Philips ones and replaced the ballasts too. The light performance is so bad on these things. They are only low-beam, but its dangerous to drive at night in my opinion.

Previously a Forester owner (twice) I had a Philips H4 LED kit in the '06 Forester, then I had factory lights in the '16 Forester, both were fine.

So I have decided to go back to LED in the Liberty and have bought some D2S LED bulbs (with their own in-line ballast).

Now for the install, this is where my question comes in.

Will there be enough juice available on the 12v rail, in-front of the HID ballast (I will unplug the HID ballast but leave it in place to waterproof the whole light fixture), or should I use a relay. Given the LED's are 100W, they will draw about 8ampers at 12v.

Thanks for any advice ! It's a bit of a job to remove the front bar, to then have to figure all this out on the fly. Its my daily driver and I just wont have time to stuff around once the bar is off.

Many thanks for any info. Does anyone here have a workshop manual for the 2011 Liberty GT ? That would help me lots.
User avatar
evilsim
 
Posts: 2
Joined: Sat Nov 07, 2020 7:11 pm
Location: Sydney
Car: 2011 GT Liberty

Re: 2011 Liberty HID changing to 100W LED

Postby bigBADbenny » Sat Nov 07, 2020 9:21 pm

FSM link in my signature.

Personally, I’d grab a spare set of headlights, do the led mod and restore/recoat the lenses.
I use 2k clear from paint spot :good:
User avatar
bigBADbenny
 
Posts: 10450
Joined: Tue Oct 04, 2011 6:36 pm
Location: Collingwood, Melbourne
Car: MY07 GT-B 6MT OBP Wagon
Real name: Ben Richards
Profile URL: http://tinyurl.com/agvbzop

Re: 2011 Liberty HID changing to 100W LED

Postby fedaykin » Tue Dec 08, 2020 1:14 pm

Your outer lenses must be clear. I bought new ones from alibaba, money well spent.
You need to inspect your bowls (where the bulb sits), reflective coating most likely damaged/burnt.

I replaced burnt bowls and the outer lenses, headlights look like they're from a new car.
fedaykin
 
Posts: 674
Joined: Wed Apr 08, 2015 10:09 am
Location: Sydney
Car: MY10 GT Wagon 6MT

Re: 2011 Liberty HID changing to 100W LED

Postby evilsim » Fri Sep 01, 2023 2:00 pm

good advice all thankyou - however i am looking to sell my beast to get a Forester so I can carry more stuff around for my kiddies

I did end up changing the HID to LED and got some improvement, however my lenses are still unclear and not nearly as bright as i'd like. My yellow fog lights are brighter!
User avatar
evilsim
 
Posts: 2
Joined: Sat Nov 07, 2020 7:11 pm
Location: Sydney
Car: 2011 GT Liberty

Re: 2011 Liberty HID changing to 100W LED

Postby Yowie » Fri Sep 01, 2023 9:00 pm

Welcome to the Forester-owning community.

Your enlightenment transcends your headlight solutions.
User avatar
Yowie
 
Posts: 599
Joined: Tue Jul 21, 2015 10:05 pm
Location: Brisbane
Car: SH Forester XT


Return to Bling me up

Who is online

Users browsing this forum: No registered users and 1 guest