This looks like good value (Perrin TMIC)??

by **GTBR46** » Tue Jul 28, 2009 4:50 pm

AVOs is about $1300.00

Perrin : $925 ish? http://cgi.ebay.com/ebaymotors/Perrin-P ... ccessories

by **dwayne** » Tue Jul 28, 2009 6:15 pm

Followed that link and it was $800 US, which at todays live exchange rate (of $USD0.832) works out at over AUD$960. It then ships from the US, which would cost a fortune to get over to Oz.

was it a different link you meant to post ?

Cheers

Dwayne

by **GTSPECB STI** » Tue Jul 28, 2009 6:44 pm

By most accounts the Perrin is good piece of gear but not sure its any better than the AVO. As previously stated the Perrin will cost you alot more to land in Oz than the AVO purchased locally. I have the AVO and its better than the stocker but not outstanding..does the job as they say.

by **Spec B Wgn** » Wed Jul 29, 2009 11:03 am

i reckon the hypertec is a better proposition

having seen one on michaels GT and the results he got, that would be my choice.

viewtopic.php?f=10&t=4085

by **Johnb** » Wed Jul 29, 2009 11:36 pm

I bought my AVO TMIC direct from AVO Australia 6 weeks ago and I got charged $799.00 (just like the catalogue says) with a few other bits and pieces. And I'm very happy with the 183.7kw atw my car is producing (Phat exhaust, K&N filter, silicon inlet/intake/throttle body hoses).

I've made several enquiries of US parts suppliers and mailing out a single part is few expensive but it gets a lot cheaper per part when you order lots of parts.

by **sundayDriver** » Thu Jul 30, 2009 9:14 am

With all these after market TMIC, I'm guessing they all require the engine shroud to be trimmed/removed/replaced, yes?

by **smythie** » Thu Jul 30, 2009 9:18 am

Some do, some don't

by **GTSPECB STI** » Thu Jul 30, 2009 9:54 am

I bought the AVO TMIC for $800 from AVO Melb some time ago. fitment was no issue and it works well. I am sitting around 175 kw and 415 Nm but expect more with a new tune planned. The engine cover does not fit with the AVO TMIC but you could trim it a bit and get it to fit. I have not bothered.

by **overl0ad** » Sat Aug 01, 2009 10:33 am

GTSPECB STI wrote:I bought the AVO TMIC for $800 from AVO Melb some time ago. fitment was no issue and it works well. I am sitting around 175 kw and 415 Nm but expect more with a new tune planned. The engine cover does not fit with the AVO TMIC but you could trim it a bit and get it to fit. I have not bothered.

just wondering if the bonnet still "seals" around the TMIC without the engine cover?

This looks like good value (Perrin TMIC)??

This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Re: This looks like good value (Perrin TMIC)??

Who is online