Page 1 of 2
Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:29 pm
by gtsubi
You guys are probably not going to beleive this but i spun my bottom end bearing 6 months ago and last week I did it again after getting it fixed by doing and engine rebuild for $5,000. I dont want to do another engine rebuild!!!
I bought the car for $16,000 8 months back and blew it at 130,000 kms. After doing the rebuild I did 10,000 kms on the new engine then blew it again.
Ideas? Options? ?!?!?!?!?!
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:36 pm
by bosc0
Take it back to the engine builder?
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:38 pm
by Robbks
What are you doing to it to keep blowing it up,
Who's the builder
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:40 pm
by gtsubi
lol, it was a job done in Fawkner/Broadmedows in Melbourne. Dodgy suburbs
Cash job, no receipt, no warrenty, was a better option than Subaru charging me $9k for a build
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:43 pm
by Robbks
No Receipt does not man sh!t.
you paid $5k for an engine that should under reasonable circumstances last much more than 10,000km
If it's faulty workmanship on their part you are entitled to receive replacement/ repairs/ refund of the goods.
Have you had the failure diagnosed as to what caused it.
If not, that is the first thing to do.
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:46 pm
by kiahatsiu
Same tune? Much knock?
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 3:58 pm
by garbo41610
gtsubi wrote:Cash job, no receipt, no warrenty, was a better option than Subaru charging me $9k for a build
Apparently not...
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 4:10 pm
by gtsubi
FYI car is STOCK
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 4:12 pm
by Robbks
OK, so what else was wrong with it?
what happened at the time of it dying?
what fuel do you use?
what caused the first failure?
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 4:14 pm
by Hotwire
kiahatsiu wrote:Same tune? Much knock?
gtsubi wrote:FYI car is STOCK
This. Stock tune on MY04 - are you ALWAYS running 98 fuel and how do you drive?
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 4:17 pm
by gtsubi
always run 95 premium - BP
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 4:19 pm
by gtsubi
Robbks wrote:OK, so what else was wrong with it?
what happened at the time of it dying?
what fuel do you use?
what caused the first failure?
thats it, nothing else, just the knocking noise, car is stil driving, but don't it'll drive much more.
last time, when it first happened, the engine just ceased, but now its still going coz its still new noise.
i use 95 - BP
HAHA the first one, i bought the car private, did RACV check, 6 hours after getting the car, bottom end bearing spun :s daafuqq? so had to cop it and repair it.
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 4:20 pm
by Hotwire
There in lies your problem. Stock tune on MY04 is prone to detonation even with 98 RON fuel, which the user manual states is the minimum RON fuel. By running 95 octane your engine is constantly detonating... sounds like you've done the damage through use of incorrect fuel.
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Tue Apr 23, 2013 5:28 pm
by gtsubi
Well anyhow not going to repair it twice in my life. Putting it up for sale. And wait for someone who wants to fix an engine for more performance
Re: Liberty GT 04 - Bottom End Bearing! TWICE

Posted:
Wed Apr 24, 2013 12:18 am
by jslayz
New short motor from Rising Sun Subaru - $2200
Competent mechanic to install - $2000
Think you got done over at 5K
I'd be going back and causing them a great deal of trouble by exercising every right & complaint process available.
J