Page 1 of 32
Extractor Manufacturing
Posted:
Tue Oct 18, 2011 10:04 pmby Tradewind
I am considering manufacturing EZ30D exhaust extractors and this poll is about gauging interest, if very low amount of hits I will not produce extractors, if strong interest then ...................we do
Material will be exhaust grade stainless
Design will have a likeness to the form of the K2 headers
10mm flanges
No cats included
I expect to have a set made prior to Xmas this year
Other thoughts and opinions are welcome
EZ30D characterised by following features
EZ30D: 2999CC DOHC, 245ps (180 kW) @6600rpm, 297Nm@4200rpm. Bore 89.2mm, Stroke 80mm. Compression 10.7:1. This version had one exhaust port per cylinder, a drive-by-wire throttle, a black plastic intake manifold, VVL and AVCS. It was available in manual and automatic unlike the old EZ30D. Found in the 2003-2009 Legacy 3.0R, Outback 3.0R and 2006-2008 Tribeca.
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 7:46 amby garbo41610
Don't tell PowerChip about the possibility of the extractors looking like someone else's product...
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 8:44 amby Doyab
Just to clarify ez30d and not ez30r?
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 9:57 amby Tradewind
Doyab
There are Liberty's known as 3.0R but there is no engine designation of "R" for the EZ30
I added extra info to the first post
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 10:24 amby Doyab
That quote is from wiki. Sometimes unreliable. There is a ez30r.
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 10:48 amby Robbks
Doyab.
you have a gen4, look at your engine code on your Build plate
EZ30Dxxxx
the EZ30R name has been widely adopted as a way to distinguish the Gen3 Outback EZ30D's from the Gen4 (3.0R) EZ30D's
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 11:06 amby Doyab
Well there you have it. Learn something everyday. Thanks for the information.
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 11:33 amby Doyab
Other then wiki, I still can't find anyone else referring to the 2gen ez30 as ez30d
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 12:09 pmby Robbks
Subaru parts software (Fast2) shows EZ30D for my Gen4
Re: Extractor Manufacturing
Posted:
Wed Oct 19, 2011 2:26 pmby Tradewind
Kiks put everyone straight on this a while back
If you look on engine casting its just Z30 if I recall, will look again sometime, can see it from drivers side under the plenum runners
Re: Extractor Manufacturing
Posted:
Thu Oct 20, 2011 8:13 amby Tradewind
Extractor manufacturing a no go at the moment
Re: Extractor Manufacturing
Posted:
Fri Oct 21, 2011 2:05 pmby Egg
garbo41610 wrote:Don't tell PowerChip about the possibility of the extractors looking like someone else's product...
Dude better be carteful...if he gets wind u typed his name he might sue you
Re: Extractor Manufacturing
Posted:
Fri Oct 21, 2011 6:53 pmby kiks
Are these genuine cargraphic?
Re: Extractor Manufacturing
Posted:
Fri Oct 21, 2011 7:28 pmby Tradewind
Kiks
????? Missed the message there
Re: Extractor Manufacturing
Posted:
Sat Oct 22, 2011 2:01 pmby kiks
besanko'd