club.liberty.asn.au

Sat ..few of us went over to phat's place for ....... u know what !!!
i was there at 8am ... while da man was still ZZzzzzz ... then follow by the chris.. then we went for a drive to pick up few parts and went to have pho for lunch ... once franky & brand was there the driveway was like this ... hahaha..

First patient was hks 180 ........ time for some boost !!


next was chris ....... to fit the engine cover .... i was thinking .. man can't be that hard to fit the cover rite .. !! hhmmm i was wrong ..!! hahaha
bcoz of the hyperflow top mount chris had .. he was having problem putting the cover back on ... but after phat ... chop the cover a bit and push & pull the top mount ... ( while 5 of us watching phat ..almost pull the engine out ) .. it went in with out any problem !!

and this is our work shop under the rain !!! and the phat with out hia head !!

finaly patient was franky !!! mmmmm defi !!!


hhmm that looks like a fighter jet ..... 4 different place telling him what boost his running ..

and last patient left at around 8ish ....
after everyone left me & mike went to a thai place at fairfield for dinner !
man it was nice !! mm the duck egg .... yum yum
so that was my work shop day report ..... Thanks mike for his time installing all these mod for us ....... his knowledge is priceless ... i guess he got them by getting his hand dirty !!

Leo

haha well done LEO!!!!!!!! u guys lucky to get mod :'( hehe

Hows the boost now Leo? do you go weeeeeeee?

Defently wish I coulda made it.. I want mods installed lol

chris & franky .. help me set up the boost ... thanks guys !!
low was set on 0.9 bar and high is on 1 .... even tho stock is 1bar ..
but when it set on high ... same 1 bar the car feel ....... woooooooo ~

so think i'll stick with 1 bar for a while till ...... the car is ready for more !!

this the where i put my controller fot the evc .......
mike said ....... r u sure ?!?!?! i said .......... CHOP IT !!! and this was the end result !! hahahaha love it ......... sometimes u need to take bit of risk ! but not too much ,,,, other u get .. boonnnnngggg ,, !!





Leo

haha nice little sneeky spot dude looks smicko..

what did u have to cut?

no more smoking !! hahahaha -- ash tray is gone !!! bye bye !!

lucky i don't smoke !!!!

lol yeah

But did u have to cut anything? or u just pull it out and then u can just sit it in there etc.. or is it fixed to something etc...?

yeh u have to cut the side a bit .. and slide the controller in ..

Arrrhh sweet sounds good man... we are post whoreing!!

SHould post it up in the DIY Mods

hahahahaha ....... i got so much work to do ..but ,,,,,,,, need to relase some stress !!!

and mike did the chopping for me so .......... his the man to talk to if u have any question ... but i think it's not too hard ..

first u need to remove the whole ash try ... even the spring loaded plate for the tray ... then u cut the side a bit.. (the 12v outlet side) then the controller will just slide in and ........ SUPER glue it !!!

great pics and report leo.

gotta say thanks to the phat man again for the work he's done for us over the last few weeks. very much appreciated dude.

fish

Leo,
can you comment on your car's performance with boost set on high compared to stock?

looks good leo, how high you wound the boost up so far ?

how high can it be wound up safely with minimal mods?

Thanks for being photo man Leo.

Fun Day!

et wrote:Leo,
can you comment on your car's performance with boost set on high compared to stock?

from what i know .. stock boost is 1 bar ... but when i set my high boost at 1 bar .. i can fell the extra kick when the boost hits .... even tho both are 1 bar ... but the evc 1 bar kicks harder !!

so a dyno run would be good .... so i can see the difference !! ^^