club.liberty.asn.au

Hello all!

After spending the last year in a MY08 NA 2.5i i decided to upgrade.
Upgraded rather nicely to a MY08 tbSTi Wagon 5AT To say i have been enjoying the last week driving around would be a gross understatement!!

Anyways enough of the jibba jabba now to the goodies / future goodies on the car.


MODS LIST:

INTERIOR:
Factory OEM Sat-Nav
DAMD Flat bottom steering wheel - Red Stitching
LED replacements for map, dome & boot.
Black Prova Si Drive Knob
Re-Upholstered centre console lid with red stitching
Group Buy 3D Floor Mats


EXTERIOR:
LED replacements parkers, fog lights, reverse, number plate lights
6000k Low Beam
Valenti LED rear lights
Cyber-R Big Bulge Scoop
OEM Mud Flaps
OEM slimline weathershields
Custom Plates - White on Black


HANDLING / WHEELS / BRAKES :
Enkei RPF1 - Silver 18x8 +35
Bridgestone RE050a and RE002 in 225/40/18
Shockworks Coilovers
Front = 350mm centre hub to arch
Rear = 355mm centre hub to arch
White line KCA313 Correction Kit
Whiteline KCA334 ALK Front Kit
Whiteline KCA339 Rear Camber Bolts
Whiteline Rear Swaybar 22mm - Adjustable
Whiteline Front Swaybar 22mm - Fixed
Whiteline Adjustable Endlinks F&R
AVO HD Rear Swaybar Mounts
Project MU NS400 pads F&R
DBA T3 Slotted Rotors - Front & Rear


ENGINE BAY / EXHAUST / PERFORMANCE:
Kido Tuned
Invidia Aus Spec Dump Pipe
Fujitsubo Cat-Back Exhaust
ProcessWest TMIC
HKS Super Hybrid Panel Filter
Turbosmart Kompact Plum Back BOV
Perrin Silicone SFB @ Turbo Inlet hoses
Cusco MBC Stopper
Cusco Radiator Shroud
STi Radiator Caps
STi Magnesium Oil Cap
JDM Battery and ABS Covers
Torque Solutions Billet Pitch Stop
Torque Solutions Engine mounts
Grimmspeed 3-Port BCS
Saikou Michi S1-DC3 twin OCC's


FUTURE MODS:
Cosmetics:
Delta speed side/rear skirts
JDM Rear bar - thin lip goodness
Brembo Re-Paint
Vinyl Wrap/Re-Spray
Red front seatbelt webbing

Performance:
COBB Performance CAI
Upgrade turbo


PICTURES:

Love it mate good work! Was this one from a member on here?

Yeh was OllieJ's old car.

If you are down at the next meet may have to get you to take some proper shots of the car not from a phone haha!

I hope to make this upgrade one day!

Nice

I take the visiting rellies out to lunch, and in that time you've scored olliej's car

Congrats to you both!

Tasty wag!

champ wrote:I take the visiting rellies out to lunch, and in that time you've scored olliej's car

Congrats to you both!

A lot can happen in a short space of time can't it!

The upgrade is a must digital, nothing better than getting sucked into the seat when the turbo kicks in haha!

Nice work bezza

Looking good! Was/is a great set of wheels

If you need the stock mid pipe for the new muffs ive still got it, the fujitsubo mid pipe is bespoke for its muffs.

Mm I may possibly Ollie.
Not a certain to get them as yet but it's a possible.
The fujitsubo has a nice note, not too loud nor too soft

Congrats Ian, looking forward to seeing this in the metal

Most important mod went on the car today, club.liberty sticker in stealth charcoal!



Also am waiting on Whiteline ALK, engine mounts and billet alloy pitch stop brace to arrive.
Hoping will make the car a little more stable and less movement.

Post up how it all goes once installed

Alright guys looking for some advice.

Planning on pulling off the front bumper/lights to black out this inside this weekend (finally some sunny weather!!!).

Going to do the oven method to release the sticky seal of the lights.
Any idea what temp to do it at? 100C be too much? How long to leave in there?

Also will i need any extra sealant when placing back together or just back in the oven to soften up and whack together?

Please help really don't want this to go wrong haha!

Bezzza wrote:Alright guys looking for some advice.

Planning on pulling off the front bumper/lights to black out this inside this weekend (finally some sunny weather!!!).

Going to do the oven method to release the sticky seal of the lights.
Any idea what temp to do it at? 100C be too much? How long to leave in there?

Also will i need any extra sealant when placing back together or just back in the oven to soften up and whack together?

Please help really don't want this to go wrong haha!

Think there is a thread somewhere on this forum as a DIY walkthough, if not HKS180 would be your man to pm regarding anything lights!

good luck and be sure to post pics!

I have had a poke around but can't seem to find much as far as walkthroughs :s

Might shoot Leo a pm is a good idea, see how he is doing his halo installs