JSLAYZ - 283awkw pics pg 39,41,53,55,63

[jslayz]

Headers still cold but you get the idea.
The whooshing spool sound does not come through well, oh well.

[Boostaddict]

Sounds nice man.

It doesnt look that fast tho?? Never does i suppose

[jslayz]

Not going flat out as car only just warmed up n oil temperature not up yet either

[Boostaddict]

Was going to say.!!!

Nek minit 4 wheel skids video uploaded!!!

[jslayz]

Hi

We have ignition!

Ordered ATF thermostat in preparation for my WTA install.
Radiator being replaced by 18mm koyo.

Have specced my WTA components and will place order after double checking all diameters.

Will be a squeeze but will get it in.

So exciting to be ordering more hardware, mmmmmm!

J

[jslayz]

Forgot to mention.
Had retune last week by the way n now have 21psi at 3200rpm.
Drivability is now MUCH better....
Have hit 22psi a few times now too with no issues.
Video was on old tune.

J

[<GB>]

Frozen boost? or plazmaman or another brand?

[jslayz]

Frozen boost Type 26 & Type 101.
Yes I will be 'making' it all fit

See how this goes, gonna take 2 weeks off to do it.
Will also finally get all my gauges installed too.

I will also be going E85 after this is all in too.

300hp at the wheels is good but.......whatever I end up with after this round will be better

J

[<GB>]

Frozen boost Type 26 & Type 101.
Yes I will be 'making' it all fit

See how this goes, gonna take 2 weeks off to do it.
Will also finally get all my gauges installed too.

I will also be going E85 after this is all in too.

300hp at the wheels is good but.......whatever I end up with after this round will be better

J

That's a big set up I was looking at type 17 with type 118 with another small core mounted above the rad support, I want to put my roe back in

[jslayz]

any particular reason to go the type 17?
Dont think I would be able to use a type 17 as I need a catch can installed in that area too.

Looks very large.

I'm going for a higher ratio of surface area of the front heat exchanger to the intercooler.

J

[jslayz]

Have gone Type 26 and type 101 and the bosch cobra.
Looking forward to this turning up in a few weeks.

In fact, hanging for this to turn up in a few weeks!!!

Will take some snaps of the install too.

J

[<GB>]

any particular reason to go the type 17?
Dont think I would be able to use a type 17 as I need a catch can installed in that area too.

Looks very large.

I'm going for a higher ratio of surface area of the front heat exchanger to the intercooler.

J

well it looked like a better fit and I would modify the end tanks to point towards the throttle, my catch can is in a different location, im interested to see how your set up will look cause I did some measurements and that wta didn't look like it would fit. if I didn't run that I wanted one made by cxracing its 16in x 11in x 4.5in core 11inx9inx4.5in intake goes straight in and the outlet is at 90 deg

I wanted a bigger water reservoir but didn't think 3.5 in thick would fit my bar, if yours fits I might try lol

plazma man made one that suit 800hp but they want drug money for there stuff

[shav]

Have gone Type 26 and type 101 and the bosch cobra.
Looking forward to this turning up in a few weeks.

In fact, hanging for this to turn up in a few weeks!!!

Will take some snaps of the install too.

J

The bosch cobra units are far better than the standard alternative. Love what your doing with this and super keen to see how it all pans out for you. Depending on how it works for you, I will be tempted to go this route myself.

[<GB>]

I made a box to suit the size so see how well it fits, sits under the reo fine hangs a little low, are you planning on having a reo?

[jslayz]

What is a reo...?