club.liberty.asn.au

Well, i don't usually do stuff like this, but figured i might as well.

Car: 2008 Subaru Liberty GT Spec B.
Colour: Diamond Grey
Trans: 6MT
Power: 212kw (tuned by Cihan @ Edge Motorworks run-in tune)



Engine/Drivetrain:

PHAT Dump pipe
Custom exhaust. 3" Center with straight through muffler, split to 2 x 2.1/4" with glasspak mufflers and quad tips (thanks to Barney at Hallam Performance Exhausts)
Cobb SF Intake
Perrin Turbo Inlet Pipe
TD05-18g
Turbo Blanket
Tamioka Throttle Body Hose
Samco Radiator Hoses
ID1000 injectors
One step colder spark plugs
Kando UEL headers
Pierburg 3 port boost controller
TGV deletes
Ported Heads
ARP2000 head studs
Air pump deletes
ARP forged rod bolts
ACL race bearings
Cosworth Pistons
Cosworth rings
Turbosmart kompact bpv
Innovate LC-1 wideband
Perrin TMIC
Intercooler Waterspray kit controlled by hobb switch
Optima Yellow Top battery
Exedy HD clutch
Sports Flywheel

DBA4000's slotted rotors front and rear (thanks to Adam at tuspeed.com)
Project Mu pads front and rear (Cant remember the exact model but they are green, also sourced from tuspeed.com)
Endless RF-650 brake fluid

Interior

JDM Clear Door Courtesy Lights cover
Digital Vent Boost Gauge
Aux input for McIntosh system
LED Dome light
LED Door lights
LED Map lights
LED Strip x3 in Boot
Vent Boost Gauge

Exterior

Painted brake calipers with red caliper paint
Tint front windows (thanks to Rob Tait)
LED front parkers
LED indicators
LED number plate lights
LED Puddle Lights
Angel Eyes
8000k HID headlights
8000k HID Fog lights
Bonnet Hood dampers
Reverse Camera integrated into factory sat nav (Sharp brand camera)











Reverse Camera in action:


Reverse Camera @ eye level:




The 4 PIN white plug that I tapped into for the reverse camera. Plug is identical to a PC PSU cpu power plug:


Rear Rotor:


Planned Future Mods:
Number plate change black/grey.
Perrin Top Mount
New Turbo (Maybe a TD05-18g still trying to work this out)
Bigger Y split in exhaust (2.5" or 3" depending on requirements for turbo)
Longer term mods:
Coilovers (Maybe BC BR?)
Aftermarket rims (most likely 19")


So that's it from me, i'll post pictures and update when i can. : )

Just wanted to thank everyone on the forum for being so friendly and helpful. It really has made the journey so far quite enjoyable.

Brian

Very nice Brian, great taste there with all those mods.
Looks like there may be a flood of libs heading over to Danny at springy motors too

Good to see your profile Brian. Never could quite exactly remember all the modifications you have done on your beast. Good choice on the mods, i would have done the same if i had a gt.

Need moar pics haha, excellent nonetheless!

Bryan?! Great result from springy! and like I said to you before love the colour of your car....very unique.....nice work!

For your requirement and aim...a TD05 18g / 20g will be perfect! 2500/2700 RPM - 5000/5500 RPM

enjoi!

Very nice Brian.

Rims will totally change the look of your car.

Brain! Love your car! very sleeper! hope to see you & your car again!

Here is another shot of your car, hope you dont mind.

Last photo does that car some serious justice!

Nice ride mate!

Very nice ride there and awesome mods and plans.

Brian Brian Brian Brian.....where did you get this???? i love it...

Anthony, thanks! That is an awesome photo!

Thanks everyone for the kind words! If it wasn't for everyone here..... Well i don't even want to contemplate that idea... Who knows, my car would probably still be stock...

Hey jack, love the work you've done to your car. You've been quite busy! I got the gauge from here: http://www.gtboostgauge.com/

There's a thread on legacygt which is how i discovered it. I like keeping the look clean without stuff sticking out where it's not supposed to be, so i was quite impressed when i saw that!

The thread is here if you want to read on the progress and stuff: http://legacygt.com/forums/showthread.p ... oost+gauge

Thanks again everyone!

AWESOME.....I'll check it out...your a champion...i love the sleek look...not a million gauges everywhere..was it hard to install?

The website says they're out of stock...bummer

....can't wait for your td0518g... (:

Nice and neat Brian.

*Updated first post with the exhaust change. Removed the resonator and threw in a straight through muffler. Took out the last little bit of drone that was in the car, quietened it down a little bit and still has the winning note.

Jack - The gauge was very easy to install but i believe he is having some sort of issue with them and that's why it's not available atm.

Sensational set of mods .... Very crisp.

Love that boost controller !